Kelco Pump Controller QR Codes

Kelco Controller QR Code Information

Please follow the link for your product below for the switch installation guide and data sheet:

F60-MK3 Pump Controller

F29-MK3 Programmable Flow Switch

E30-MK2 Programmable Pressure Switch

IPG20-MK3 Intelligent Pump Guard


LM Series Side Entry Level Switch

kadmin

Features

  • Australian Made
  • Heavy Duty 316 Stainless Steel Switch Housing
  • Built in Manual Override
  • 15Amp 500V SDPT Switch
  • Low Voltage option available with Gold Contacts
  • Seal-less Magnetic Drive
  • IP67 Weatherproof Rating
  • Simple to Install
  • Fully Serviceable

Description

The LM Series is a super tough switch is a reliable and accurate solution to tank level control. The switch housing is made from 316 Stainless Steel and machined aluminum and has a glass-reinforced Polypropylene arm and float. With the LM Series you have the option of a 1″ BSP or 1″ NPT metal process connection.

These switches is supplied with a standard Max. 500V SPDT microswitch for general control circuit use. The LM Series level switches are built tough to give a long reliable service life in the most arduous of applications.

See the data sheet linked below for more information on the available models in the LM Series and the ordering codes.

More Information

Share

For assistance in choosing the correct product for your needs, check out our Product Selection Guide. 


CR22 Microwflow Switch

kadmin

Features

  • Australian Made
  • Can detect flows of less than 500 mL per Hour
  • Maximum flow rate of 4L per Minute
  • Suits tube and pipes from 6mm to 20 mm
  • All wetted parts UPVC with VITON® seals
  • Compact vertical position mounting
  • 18 Bar 260PSI Pressure rating
  • Fast response to flow loss
  • Easy to install and service
  • Simple and reliable
  • Weatherproof

Description

The CR22 microflow switch operates on the displaced piston principle. Process liquid passing upwards through the switch lifts a precision piston. Every time the piston is lifted a magnet sealed inside it actuates an external reed switch.
The reed switch provides a signal indicating flow. The CR22 can be setup as a normally on or a normally off switch that responds either to flow, or to loss of flow.

More Information

Share

For assistance in choosing the correct product for your needs, check out our Product Selection Guide. 


KP Series Probe Level Switch

kadmin

Features

  • Australian Made
  • No external moving parts
  • Reliable solid construction
  • S.P.D.T three wire switch
  • PVC and Polypropylene construction
  • Wide range of cable lengths available
  • Stable repeatable switching action
  • No mercury or lead components
  • Compact size, 25 mm diameter
  • Optional cable weights available

Description

The KP probe level switch consists of a vented UPVC housing that contains a Polypropylene float. Rising liquid level causes the float to lift and actuate a magnetically coupled reed switch within the switch head. A falling liquid level allows the float to drop de-actuating the reed switch.

The KP series probe level switch is a compact three-wire float switch for highly accurate and repeatable single point level sensing and control applications. It is ideal for use in water, sea water and most acids and alkali solutions. It will provide a stable switching action with a very high degree of reliability and repeatability. These float switches can be reliably and safely used in potable water systems as they do not contain hazardous materials such as mercury or lead.

Applications

  • Deep well bore pump protection
  • Suitable for saline water use
  • Withstands most common chemicals
  • Bilge level control
  • High & Low level alarms
  • EX Applications
  • General purpose liquid level sensing

More Information

Share

For assistance in choosing the correct product for your needs, check out our Product Selection Guide. 


IPG20 MK3 Intelligent Pump Guard

kadmin

Features

  • Australian Made
  • Learns the operating pressure
  • Fixed or travelling irrigation systems
  • Compensates for change in terrain
  • Cyclic running for pod systems
  • Leak and blockage detection
  • Loss of flow protection
  • Displays pressure and set points
  • 20 Bar / 2000 kPa pressure rating
  • Multi voltage operation
  • Manual or Automatic operation
  • IP67 Weatherproof Rating

Description

The IPG20 MK3 Intelligent Pump Guard ‘learns’ the operating pressure each time the system is started and then applies the predetermined under and over pressure set points. This allows for highly targeted leak and over-pressure detection. Designed for either fixed pods or travelling irrigators.

More Information

Paddle Trimming Calculator

The paddles for our IPG20 MK3 Series switches come in set lengths. These paddles can be cut down to suit your pipework and flow rate. We recommend using our Paddle Trimming Calculator to find the correct paddle length for your application.

Share

For assistance in choosing the correct product for your needs, check out our Product Selection Guide. 

3D Model & Download

     

TWM Trailing Wire Flow Switch

kadmin

Features

  • Australian made
  • Unique trailing wire type sensor
  • 0 to 500V AC 15 Amp S.P.D.T switch standard
  • High impact billet aluminium housing
  • 316 Stainless Steel process connection
  • 1″ models available with BSP or NPT
  • Suitable for harsh mining applications
  • 400 Bar 5800 psi pressure rated
  • Manual override built in
  • Seal-less magnetic drive
  • Fully adjustable
  • Easily serviceable

Description

The TWM trailing wire flow switch is supplied with a 316 stainless steel process connection and is available with a 1” BSP or NPT thread. The switch housing is machined from solid billet Aluminum. A 500V Single Pole Double Throw (S.P.D.T) microswitch for general control circuit applications is supplied as standard with the TWM.

A unique feature of the TWM flow switch is its built in manual override. Using the manual override allows the system to be manually started at any time by simply pressing the button. It also makes testing and commissioning of systems very simple.

The TWM flow switch is available with wire sensors in various lengths from 50mm to 300mm (2” to 12”). The required wire length must be specified when ordering. The flow rate required to actuate the TWM will depend on many variables such as turbulence, liquid viscosity and the surface area of sensor wire exposed to the flow.

See the data sheet linked below for more information on the available models in the TWM Series and the ordering codes.

More Information

Wire Trimming Calculator

As with our Paddle Flow Switches,  the Trailing Wires for our TWM Series can be cut down in length to suit your pipework if needed. Please refer to our Paddle Trimming Calculator to find the correct wire length for your application. The width of the wires is 2mm.

Please note that if you do cut down the length of your trailing wire, you must either silver solder or tig weld the end of the wire to prevent fraying.

Share

For assistance in choosing the correct product for your needs, check out our Product Selection Guide. 


FM Series Paddle Flow Switch

kadmin

Features

  • Australian Made
  • 0 to 500V AC 15 Amp S.P.D.T switch
  • 316 Stainless Process Connection
  • Super Tough Billet Aluminium Housing
  • Manual override built in
  • 3/4” & 1” models available with BSP or NPT threads
  • 400 Bar (5800 psi) pressure rating
  • Seal-less magnetic drive
  • Dieselene & High Temperature versions available
  • Weatherproof IP67 housing
  • Easily serviceable

Overview

The FM Series flow switch is built tough for the most arduous industrial and mining applications.

It is a rugged but highly sensitive paddle flow switch suitable for a wide range of flow sensing applications. The FM Series flow switch can be supplied with a glass fibre reinforced Polypropylene paddle, or a Nickel Copper alloy paddle suitable for use with diesel and high temperature applications.

A unique feature of the FM flow switch is its built in manual override. The manual override allows the flow switch to be switched on at any time at the press of a button regardless of lack of flow.

A magnetic coupling system is built into each FM flow switch and couples the paddles movement to the high compliance switch through a solid wall of stainless steel and aluminum. The result is a high-pressure flow switch with no seals diaphragms or bellows or other points of potential failure. The switch is suitable for use in bore water, sea water and in many chemical solutions.

See the data sheet linked below for more information on the available models in the FM Series and the ordering codes.

More Information

Paddle Trimming Calculator

The paddles for our FM Series switches are supplied at a set length. The paddle can be cut down to suit your pipework and flow rate. We recommend using our Paddle Trimming Calculator (linked above) to find the correct paddle length for your application.

Share

For assistance in choosing the correct product for your needs, check out our Product Selection Guide. 

3D Model & Download

     

F60 MK3 Advanced Pump Controller

kadmin

Features

  • Very simple to program
  • Multi voltage operation
  • Displays pressure and set points
  • 15 programmable timers
  • Powerful 40Amp solid state switch
  • Dedicated alarm relay
  • Detachable electrical housing
  • 20 Bar 290 psi pressure rating
  • Suites pipes 25mm (1″) & Larger
  • Accepts remote input
  • Weatherproof IP64 housing

Description

The F60-MK3 Digital Pump Controller has a durable glass-reinforced polypropylene paddle and a pressure switch to ensure complete pump protection. The switch can be set to control a single or dual pump system with a wide range of functions.

For more information about the F60-MK3 please refer to the linked data sheet below.

More Information

Paddle Trimming Calculator

The paddles for our F60-MK3 Series switches come in set lengths. These paddles can be cut down to suit your pipework and flow rate. We recommend using our Paddle Trimming Calculator to find the correct paddle length for your application.

Share

For assistance in choosing the correct product for your needs, check out our Product Selection Guide. 

For technical assistance, review our FAQ Sheet or contact us for more info. 

3D Model & Download

     

F29 MK3 Programmable Flow Switch

kadmin

Features

  • 10 Programmable Timers Built In
  • Powerful 40Amp Solid State Drive
  • Dedicated 16A Alarm Relay
  • Detachable Electrical Housing
  • 18 Bar 261 psi Rated Standard Model
  • 200 Bar 2900 psi Model Available
  • Suits Pipes 1″ & Larger
  • Multi Voltage Operation
  • Accepts 2 Remote Inputs
  • Weatherproof Housing

Ordering

The F29 MK3 programmable flow switch is available in various configurations to suit specific applications. Please see the data sheet download linked below for more details about the functions of this flow switch.

We also offer a version of the F29 MK3 with a flexible metal Trailing Wire instead of a paddle, our TW29 MK3. This model is recommended for applications with flows that contain solid or semi-solid materials like sewage pumping or mining applications, where a paddle type switch would otherwise be unsuitable.

More Information

Paddle Trimming Calculator

The paddles for our F29 MK3 Series switches come with a set length. These paddles can be cut down to suit your pipework and flow rate. We recommend using our Paddle Trimming Calculator to find the correct paddle length for your application.

Share

For assistance in choosing the correct product for your needs, check out our Product Selection Guide. 

3D Model & Download